FAQ

1. Do we provide the customer with the material testing for free? What’s the material testing process?
We can provide the customer with the free testing of their material or product. Our engineer will test the best result of cutting, engraving or marking. The testing parameters, detailed pictures, testing report and video can be sent for customer’s reference. If needed, the tested material or product can be sent back to customer, and its shipping cost should be paid by customer.

2. Machine shipping cost?
Customer can choose to cooperate with your own forwarder. Also, our forwarder can take care of shipping for you.

3.What’s the delivery date?
Normal models, such as CMA series universal laser cutters, their delivery date is usually 7 working days. When in peak periods in production, the delivery date is possible to be longer. For the delivery date of other specific model, please consult with our sale representative.

4. What’s warranty content?
For normal models, such as CMA series universal laser cutters, we provide with 12 month warranty for the whole machine, except for the optical parts and wearing parts. For the warranty of other specific model, please consult with our sale representative.

5. What service will be provided in warranty?
When in warranty, the spare parts break down. We will offer to change a new one or repairing service for free. The customer is required to send back the broken parts first. Depending on the broken situation, we will decide to change or repair and then, send to customer the parts. Its shipping cost should be paid by customer.

6. What’s the after sale service?
Our after sale engineer will provide on line service 16 hours a day, by answering on line, remote control, email reply to settle with customer’s issue.
If it is needed, our engineer can do door to door service aboard, including installation and debugging, training, trouble shooting etc. The customer needs to pay us for the round tickets, insurance, visa, meal and accommodation, local traffic fee, and daily service fee.

1. Do you provide OEM service?
 Yes.

2. Can Yueming customize the machine for customers’ specific application?
  It depends on customer’s application. Please consult the sale representative.

3. How long does it take to learn to use the lasers?
  1.If you know how to use graphic design software, you can be up and running in minutes! There is no proprietary software to learn so you can use the programs that you are already familiar with to make the transition into laser engraving as smooth as possible.
 2. It will take a bit of trial and error to learn what speed and power settings to use with different materials, but we include a comprehensive guide with your system that has recommended speed and power settings for various materials with which you will be working.

4. What types of graphics can I engrave and cut?
 You can engrave scanned photos, logos, bitmaps, other images, text, and AutoCAD files. Essentially, if you can print it, you can engrave it.
To cut, you will need a vector based graphic, such as an .eps or Illustrator file.
Keep in mind the higher the quality of the graphic you're working with, the better your engraving results.

5. Can Han’s Yueming's lasers engrave on metal?
Yes. Our FiberMark systems were designed to permanently mark all types of bare metal. The FiberMark was designed with a combination of affordability and high quality results in mind. Our flat bed, flying optic design is revolutionary for a fiber laser system and will mark metals over a large work area in a short amount of time.
And, though our CO2 laser systems are mainly designed to engrave and cut non-metallic materials, they can also be used to mark on metal with the aid of metal-marking compound.

6. Can Han’s Yueming's lasers cut metal?
Specially, we launched CMA fiber laser high speed cutting machine for various thickness metal cutting. But for CO2 laser, since we use low power CO2 (30 to 130 watts) and fiber lasers (10 to 50 watts) the beam will clearly mark on coated and raw metal but our systems are not ideally suited for metal-cutting applications.
Please contact our Applications Lab to discuss your metal-cutting applications and see if they can work with our systems!

7. Is the laser safe to operate?
Yes, the laser is completely safe to operate. It is a Class 2 laser - 1mW CW Maximum 600-700 nm, which means that the laser is secured with interlock devices so it will not run with the doors of the system open. No special safety gear is required to run the laser.

8. Do I need separate laser systems for engraving and cutting?
  No, one laser does it all! Our CO2 laser systems will engrave and cut most non-metallic materials, as well as engrave coated metals. For information on what materials you can engrave and cut, visit our Materials page.
The laser can be set to engrave only (Raster Mode), cut only (Vector Mode), or can complete both operations in Combined Mode. The laser knows what portions to engrave and what portions to cut based on line width, which is easily set in your graphic design software.

               

9. What are the computer requirements?
 Investing in a new computer is a great way to make sure you’re getting the most out of your new laser equipment. Computer processing speed and memory are needed for software’s well function. A good computer won’t make a huge difference in how your laser runs, but when compared to a slow computer it will save untold amounts of time and frustration setting up the artwork that you “print” to the laser. Many users do not purchase new computers for use with their new laser because their current computers are perfectly adequate. There’s no magical cut-off that makes a computer too slow. If you’re comfortable with the performance and speed of your current computer, there’s probably no reason to purchase another one. The following recommendations are just options to consider if a new computer is necessary.
A new computer doesn’t have to be expensive to work well! Even many of today’s lower-cost computers work well for laser applications. As long as you don’t buy the cheapest computer you can find you should be fine. One thing to avoid is the Intel Celeron processor – while they are good processors, and will work with the laser, they don’t process graphics with the speed most laser users desire.

Operating System: All new Epilog lasers are designed to work with all versions of Windows 2000, XP, Vista, 7 or 8 operating systems.

The Fusion Laser Series is also compatible with Mac operating systems OS X 10.7 and higher. Read more about our Fusion Mac Driver here.

RAM (Random Access Memory): 512 MB is recommended. RAM is kind of like short-term memory. It’s fast, readily available for the computer to access and makes time consuming tasks go much quicker if you have lots of it. Most users won’t notice a difference if they add more than 512 MB to their system, but almost all uses will notice the speed difference that 512 MB provides when compared to 256 MB (256 MB is essentially the next step down from 512 MB).

Processor Speed: A faster processor will allow you to do more tasks in less time. While it’s not necessary to purchase the fastest processor available, you’ll want either an AMD Athalon processor or an Intel Pentium IV processor (do not purchase a computer that is using an Intel Celeron processor – they’re too slow for graphics applications). Processor speeds are always improving, but processor speeds of about 2.0 GHz or faster are a good place to start.

10/100 Network Interface Card (NIC): All new computers have a 10/100 network connection as standard equipment. As well as allowing multiple computers to be linked together in a network, this technology also allows direct printing from the computer to the Epilog system. Epilog supplies a network Crossover cable with each laser system that allows one computer to print to a single Epilog system.

20-30 GB Hard Drive: This is the permanent memory in your computer. Many users feel that you can never have a large enough hard drive, but for most laser applications 20 or 30 GB’s is going to be adequate for years of storage. Luckily, most computer manufacturers put at least 20 GB drives in new computers these days. When in doubt, buy bigger than you think you might need. It’s so inexpensive that it’s worth the peace of mind to have it available.
               

10. What is the repeatability of the laser systems
 0.05mm.

11. What is the accuracy of the laser systems?
 <0.05mm.

12. What is the wavelength of the laser sources?
  CO2: 10.6 microns
Fiber: 1064 nanometers

13. Can you cut or engrave polycarbonate with a laser system?
  Cutting: Thin sheets of polycarbonate can be cut with our CO2 laser systems, but the material tends to discolor when heated by the laser beam. The thinner the sheet you are cutting, the better the cutting results you will obtain. If you would like us to test your sheet of polycarbonate, please contact our Applications Lab.
Engraving: Most colored polycarbonates can be marked with our FiberMark metal and plastic marking system. To test your material, please contact our Applications Lab.

14. What materials are unsafe to engrave and/or cut with the laser?
 Hydrogen Chloride and Vinyl Chloride (mostly found in PVC and other man made materials) are hazardous to the life of your laser system. Engraving and cutting these materials can cause irreversible damage to your machine, so determining the components of your cutting and engraving materials is extremely important. Materials, such as Kydex, contain PVC.
Material Safety Data Sheet
A Material Safety Data Sheet (MSDS) is designed to provide you the proper procedures for handling or working with a particular substrate. These documents contain the elements used to make up the material and will indicate whether or not it contains elements that are potentially harmful to your engraving system.

1. Breakdown Maintenance of Laser Marking Machine  

1. Breakdown Phenomenon:
Open the key switch, no response.

Reason Analysis:
1) No power or phase loss;
2) The air switch is not closed;
3) The emergency switch is pressed.

Handling Method:
1) Restore the power;
2) Close the air switch;
3) Back-out the emergency switch.

2.Breakdown Phenomenon:
Cannot achieve anticipated marking depth

Reason Analysis:
1) The marking object is not on focus surface;
2) The F-θ lens is polluted;
3) Wrong software parameters;
4) Software output exception.

Handling Method:
1) Adjust the focus;
2) Clean F-θ lens;
3) Readjust the parameters;
4) Restart the software.

3. Breakdown Phenomenon:
When open software, it pops up “Unable to find a control card,……”

Reason Analysis:
1) No power in control;
2) The USB cable is loose;
3) The card driver is not installed;
4) The USB control card damage.

Handling Method:
1) Check if the key switch is open and switching power supply is no-output;
2) Check the USB cable;
3) Reinstall the card driver;
4) Replace the control card.

4. Breakdown Phenomenon:
No laser output

Reason Analysis:
1) Check the software setting is normal or not;
2) Check the power key is open or not;
3) Check the red light on USB control card is flashing or not;
4) Internal error of laser power supply or laser device.

Handling Method:
1) Check the software settings;
2) Open the power key;
3) Check the USB control card connection is firm or not;
4) Please contact with our technical staffs.

5.Breakdown Phenomenon:
Graphic or text marking distortion

Reason analysis:
1) No correction of software, or loss of data;
2) Wrong power supply of galvanometer power;
3) Signal interference;
4) The control card has problems;
5) The galvanometer fault.

Handling Method:
1) Adjust the parameters;
2) Adjust or replace the switching power supply voltage;
3) Check if the ground connection is reliable or not, signal line is poor contact or not;
4) Replace the control card;
5) Replace the galvanometer.

2. Breakdown Maintenance of Laser Cutting Machine  

1. Breakdown Phenomenon:
Continually light emitting after power-on

Reason analysis:
If parameter of the controller laser device are correct

Handling Method:
Correct parameters of the controller laser device

2. Breakdown Phenomenon:
Alarm given after power-on

Reason analysis:
If parameters of the controller are correct
Machine alarm signal is triggered

Handling Method:
Correct parameters of the controller
Check alarm signal source of the machine

3. Breakdown Phenomenon:
Laser pause during working

Reason analysis:
Check if water circulation is smooth
If power voltage is table

Handling Method:
Clean water tank, dredge water hose
Install a stabilizer to input power supply

4. Breakdown Phenomenon:
Wrong figure size

Reason analysis:
User adopts PLT output in CoreIDraw software. In HGPL dialogue box, if unit of plotter in page option is set correct PLT plotter unit out from CoreIDraw software should match with resolution of SmartCarve
software lead-in PLT option
If resolution of the controller parameters are correct

Handling Method:
User adopts PLT output in CoreIDraw software. In HGPL dialogue box, if zooming in page option is 100%
Change to 100%
Set to the correct resolution or equivalent

5. Breakdown Phenomenon:
Reverse direction of motor shaft movement

Reason analysis:
If setting of controller motor movement parameters are wrong
If lines from the drive to the motor are connected improperly

Handling Method:
Set to proper motor parameters
Check electric earthing

6. Breakdown Phenomenon:
Fail in movement of motor shaft or twittering of it during movement

Reason analysis:
1) Improper setting of motor parameters cause missing step to the motor
2) Damaged drive or motor
3) Motor line broken or poor contact

Handling Method:
Set to the correct movement parameters
Change the drive or motor
Reconnect the motor and drive line

Download Center Service Policy FAQ Problem Feedback Back
ec@ymlaser.com
+86 139 2589 8201
Share To